Fuel treatment

Installation of MTS-01 on a marine engine fuel line.

The device is mounted with a bypass connection.

Top view after installation.

FOR LIQUID FUEL PROCESSING: GE USM-FUEL (MTS)

After liquid fuel (gasoline, diesel, fuel oil or other) passesthrough GE USM-FUEL (or our other MTS brand), it is declusterized. As a result, the surface tension of the liquid becomes very close to the physical minimum for the given substance at a given temperature. This produces much finer droplets when the fuel is dispersed under pressure into the engine cylinder, we have better combustion, less smoke and hard particles, it increases engine efficiency and leads to fuel economy. The other effect is a decrease in viscosity. When the liquid is declusterized to a molecular level, the internal and surface friction is greatly reduced, i.e., the friction resistance decreases – the viscosity decreases to the minimum for the particular fluid.These two major impacts on liquid fuels make GE USM-FUEL (MTS) suitable for use in internal combustion engines, especially large and powerful, such as marine engines, for example; for diesel or heavy fuel oil boilers, for diesel units and others. Their other effective application is in the case of fuel lines and oil pipelines. Due to a decrease in viscosity, the fuels will be transported in larger areas with less power and less number of intermediate pressure pumps.

1.

The MTS device for ship engines. This device was developed specifically for a ship engine. MTS-01 is the only device designed to process fuel oil. When passing the heavy fuel oil through MTS-01 there is a significant drop in fuel oil viscosity. MTS-01 has been tested in real-world conditions and it works on a ship. As a result of the drop in viscosity, the oil fuel heating temperature was lowered from 130 ° C to 90 ° C, making the MTS-01 effective when operating on ship boilers, especially at margin operating modes.

The device would be particularly effective on tankers. Its effect is reflected in three major economic and environmental benefits:

1.Fuel savings of 5-15% depending on boiler operation mode;

2.Improving the performance of the machines that are currently operating at low speeds.

3.Ecological effect as a result of the reduction of nitrogen oxides, soot and carbon dioxide released into the atmosphere from 10% to 50%.

4.Reducing the number of motor cleaners, which is a significant economy for every shipowner.

GE USM-FUEL for locomotives, trucks and powerful diesel generators.

These are devices designed especially for gasoline and diesel processing. They are applicable to all types of ICE and economy is moretangible with powerful, fuel-efficient engines. The principle of operation is the same – by selecting specific parameters of the device according to the type of fuel and the engine power. The same devices are applicable to water heating and other industrial boilers using diesel or fuel oil. During the prototype study in a laboratory of the Royal Swedish Academy of Sciences, a real working process of industrial hot water boilers with heavy fuel oil showed a reduction in fuel consumption of 4% to 6% depending on the boiler operation mode. During prototype studies on the performance of heavy-duty diesel and heavy-duty construction vehicles, the results are even better: 8% – 15% fuel economy and reduction of nitrogen oxides, soot and CO 30% to 50% depending on the engine operating mode.

FOR THE MANUFACTURE OF CONCRETE AND CONCRETE ARTICLES

Due to the de-casting of water to the molecular level, internal and surface friction is greatly reduced, i.e., the friction resistance decreases – the viscosity is reduced to the minimum for the water at a given temperature. As a result, the water’s ability to dissolve reaches its maximum physical value. Specifically, in the production of concrete, this results in better wetting of the components, better cement solubility and a muchstronger mixture, respectively. This has been confirmed by research at the Chemical Technology University in Sofia, the Silikats Department, with a prototype of the device.

1.Valued indicators

– Density of clean cement paste – the least amount of water required to achieve the nominal density (ml)

–Compression strength (σ) of samples of pure cement paste (MPa)

–Strength of concrete mixture

2.Composition of pure cement paste

Cement 450 g + sand 1350 g + 30% water

3.Concrete composition – for 1 m3 of concrete

–Cement 42.5 R – 320 kg

–sand 0 ÷ 5 mm – 820 kg

–crushed stone – 5 – 15 mm – 570 kg

–crushed stone – 15 – 20 mm – 510 kg

–water required for normal pressure

•inactive – 201.6 l

•Activated by GE USM-B – 196.4 liters

Conclusion

The results obtained refer to the nominal density of the pure cement paste and the compressive strength of its samples.

Based on these results, only the GE USM-B water activator for a concrete mixture with a composition according to item 3 is used.

The use of a GE USM-B water activating device to prepare a concrete mixture with a composition according to item 3 allows an increase in compressive strength of 15-18%.

FOR AGRICULTURAL FARMING

Again, due to the decomposition of water to the molecular level, the number of unbound molecules increases significantly. This new water structure enhances the water’s dissolution capacity and, for thebetter absorption of the root system, the minerals found in the soil: nitrogen, phosphorus, potassium, magnesium and the extras: sulfur, calcium, iron, etc., as well as water. This improves the construction of proteins, the basic building block of growth and plant development.Plant diseases are significantly reduced on the one hand due to good “nutrition” and, on the other hand, due to reduced bacterial pressure due to the supply of disinfected water.The color of the leaves and blossoms becomes brighter and more intense. The improved metabolism directly affects the accumulation of foliar mass and the development of the root system and hence the increase in yields. GE USM-AGRO is also applicable for watering parks and gardens.

EXAMPLES: Greenhouse production of tomatoes and cucumbers

tomatoes
cocumber

Used activator – GE USM-AGRO

Effect of increased yields: tomatoes – 15%, cucumbers – 5%

In greenhouse production of flower seedlings and ornamental shrubs, over 10% more productivity is observed.

Effect of wheat and parsley growth:

The blue plants indicate the plants watered with activated, GE USM-AGRO water, in black – watered with plain water.

New Zealand onion results

GEUSM-Agro – with 8% less water, 7% higher yields, with bigger heads

The agro-industry has been very successful in water treatment in fish farms and shrimp farms as it solves the problem of chemical-free water disinfection which is not applicable in these cases.